IDENTIFICATION OF THE PREPARATION AND COMPANY

Product Name:
DEOXALUMINITE
Date Prepared: 1/25/08
Normal Use: Weld-through primer
Manufacturer: D-C Sales & Engineering, Inc.
Phone/Fax: Ph 262-781-7160
Emergency phone: 800-255-3924 USA

COMPOSITION INFORMATION OF INGREDIENTS


Aluminum Paste
Toluene * VHAP
Xylene * VHAP
Ethyl Benzene * VHAP
VM & P Naptha
Formaldehyde


* Toxic chemical subject ot the reporting requiremens of both Section 313 of the Emergency Planning & Community Right to Know Act of 1986 (40CRF372) and the Wisc. DNR Administrative Code Chapter NR445.
VHAP = Volatile Hazardous Air Pollutant

HAZARD IDENTIFICATION

EYE CONTACT: Liquid or vapor may cause moderate to severe irritation
SKIN CONTACT: May cause defatting and drying of skin, burning sensation or dermatitis
INHALATION: Inhalation of high concentrations of vapors may cause dizziness, breathing difficulty, headaches
or respiratory irritation. Extremely high concentrations may cause drowsiness, staggering, confusion, coma or unconsciousness.
INGESTION: Can cause gastrointestinal irritation, nausea, vomiting and diarrhea. Aspiration of material into lungs can cause chemical pneumonitis which can be fatal.

FIRST AID MEASURES

EYES: Flush with large quantities of water for 15 minutes, holding eyelids apart to flush entire area.
SKIN: Wash thoroughly with soap and water, and seek medical attention. Launder contaminated clothing before reuse.
INHALATION Move person to fesh air. If breathing stops, apply artificial respiration and seek immediate medical attention
INGESTION: DO NOT INDUCE VOMITING. Doing so may cause chemical pneumonitis and pulmonary edema. Contact a physician.

FIRE FIGHTING MEASURES

FLASH POINT (METHOD): 21C (TOC)
EXTINGUISHING MEDIA: Class B fire extinguishers (carbon dioxide, dry chemical or foam), inert dry granular material (like sand), AFFF or protein foam. DO NOT USE HALOGENATED EXTINGUISHING AGENTS. Hallin may react violently with aluminum particles. The use of water may be ineffective. Aluminum fire may react with water to form hydrogen gas. If using water, use only at a water fog setting, not a solid stream.
SPECIAL FIRE FIGHTING INSTRUCTIONS: Water spray may be ineffective. Use water to cool closed containers to prevent pressure buildup and autoignition. Product will float and can be reignited on surface of water. Self contained positive pressure breathing apparatus should be worn.
UNUSUAL FIRE AND EXPLOSION HAZARDS: This material is highly volatile and gives off vapors which may travel along the ground or be moved by ventilation. Keep containers tightly closed. Isolate from heat, electrical equipment, sparks and open flames. Sealed containers may explode if exposed to extreme heat. Do not apply to hot surfaces. This product may become electrostatically charged during mixing or pouring. Bond and ground metal containers.

ACCIDENTAL RELEASE MEASURES

SPILL OR RELEASE: Remove all sources of ignition. Ventilate area of spill and adjacent low lying areas. Remove spilled product with inert absorbent materials and non-sparking tools.

HANDLING AND STORAGE

Keep away from extreme heat or flame. Do not store at temperatures above 120F. Do not reseal container if water intrudes as explosive hydrogen may be generated. Maximum recommended shelf life 9 - 12 months from manufacture.

EXPOSURE CONTROLS/PERSONAL PROTECTION

VENTILATION: General mechanical ventilation or local exhaust should be suitable to keep vapor concentrations below the TLV. Ventilation equipment must be explosion proof.
RESPIRATORY PROTECTION: If conditions produce vapor concentrations above the time weighted threshold limit values, use a NIOSH approved cartridge respirator to keep exposure below those threshold limit values. In poorly ventilated areas, use a fresh-air supplying respirator, or a self-controlled breathing apparatus.
EYE AND FACE PROTECTION: Use chemical safety glasses, goggles or face shield.
OTHER CLOTHING & EQUIPMENT: Use of aprons or protective clothing is recommended to reduce the likelihood of skin contact.
WORK/HYGIENIC PRACTICES: Good industrial hygiene practices should be followed. This includes preventing eye contact, minimizing skin contact and minimizing vapor inhalation. Availability of eye washes and shower facilities is recommended.

PHYSICAL & CHEMICAL PROPERTIES

BOILING POINT:
93 - 204C --- 185 -485F
FREEZING POINT: NA
SPECIFIC GRAVITY: .94
VAPOR PRESSURE @20C: NA
VAPOR DENSITY: Heavier than air
SOLUBILITY IN WATER: Negligible
% SOLID BY WEIGHT: 23%
EVAPORATION RATE: Slower than ether
APPEARANCE AND ODOR: Silver liquid, pungent solvent odor
OTHER: VOC 5.92 lbs/gal

STABILITY AND REACTIVITY

STABILITY:
Stable under storage conditions recommended
INCOMPATIBILITY: Strong oxidizers and strong acids
HAZARDOUS POLYMERIZATION: Will not occur
CONDITIONS TO AVOID: Keep away from high heat, flame, spark or static discharges. Container is not a pressure vessel.

TOXICOLOGICAL INFORMATION

Product contains xylene and toluene which have been found to cause anemia, liver abnormalities, kidney damage and eye damage in laboratory animals when prolonged conditions of over-exposure existed. Xylene has been suggested as a cause of cardiac abnormalities in humans in conditions of overexposure. Reports have shown that repeated and prolonged occupational overexposure to paint solvents may cause permanent brain and nervous system damage. Product contains formaldehyde which has been found to cause cancer in laboratory animals.

ECOLOGICAL INFORMATION

There is no data available on the product itself. The product should not be allowed to enter drains or water courses.

DISPOSAL CONSIDERATIONS

Dispose of according to regulations. Do not incinerate cans.

TRANSPORT CONSIDERATION
S

PROPER SHIPPING NAME: Paint
CLASS: 3
UN #: 1263
PACKING GROUP: II

REGULATORY INFORMATION

The requirements of the classification refer to packaging and labeling of dangerous substances regulations. The product is labeled as follows:

LABEL: Flammable Liquid

DISCLAIMER

THE INFORMATION GIVEN IN THIS MSDS IS GATHERED FROM STANDARD REFERENCE MATERIALS AND TEST DATA AND IS BELIEVED TO BE ACCURATE AND RELIABLE, BUT IT IS NOT GUARANTEED THAT THE PRECAUTIONS OR PROCEDURES MENTIONED ARE THE ONLY ONES THAT EXIST. D/C SALES & ENGINEERING, INC. MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, REGARDING THE USE OF THIS INFORMATION OR THE USE OF THE SPECIFIC PRODUCT IDENTIFIED, ALONE OR IN COMBINATION WITH ANY OTHER MATERIAL OR PROCESS AND SHALL NOT BE HELD LIABLE FOR ANY DAMAGE RESULTING FROM THE HANDLING OR CONTACT WITH THE PRODUCT.






MATERIAL SAFETY DATA SHEET

CAS #

7429905
108883
1330207
100414
64742489
50000

% by wgt.

9.21
12.0
37.6
8.18
NDA
.4

OSHA PEL

15 ppm
200 ppm
100 ppm
100 ppm
300 ppm
3 ppm

813-248-0585 Int'l

FAX 262-781-3558

NA - Not Applicable